The Xiaomi Redmi AirDots are very cheap, they even take design signals from several other products on the market, but despite all that, they are quite good for the price (low).
Redmi AirDotsTrue Wireless Bluetooth Earbuds.Auto-connect once you take them out the case.
Xiaomi / Redmi AirDots, the true wireless headphones, some Devices had connection problems. This is mainly due to an incorrect coupling of the two headphones, which, therefore, cannot communicate with each other.
Contents
The procedure of Fixing Xiaomi Redmi AirDots problem is very simple and takes a few seconds.
(1)
Put your Airdrops in the box, make sure they are charged. Remove airDots from your device.
(2)
Take your both Airdrops out of the box.
(3)
Turn off both Airdrops by pressing airDots button and holding the button for 5 seconds (until you see a red light).
(4)
Perform reset :(reset of stored Bluetooth device and reset of connection between both Airdrops headphones)
To do this reset, press and hold the button on both air drops for 20 seconds (the headphones should flash after 10 seconds and 20 seconds) do not release the buttons until you see a light blink.
(5)
Turn on your Airdrops by pressing and holding the button on both for 5 seconds or put it in the box and take it out.
After done restart : on the right earpiece, you should see a white flashing light, but on the left, you should not see any light. It means that there is a connection between the headphones, and the right handset is waiting for the connection with the phone.
There we go! The AirDots are now synchronized with each other, so they are able to communicate with each-other in stereo mode.
Hare is Full video Guide
1. Gently insert the ear cap down into the ear canal. It is better that sway the head and the headphones are not shaken.
2. Please pay attention to adjust the earphone to expose the microphone during the call.
3. When talking, put the headset microphone toward the mouth to make the call clearer. The earphone itself is equipped with a medium eartip. If you feel unwell, it is recommended to replace the large or small eartip.
Before using the device, please tear off the isolation film at the charging contacts of the left and right headphones to fully charge the charging box and headphones. -Plug in the charging cable to charge both the headset and the charging box. -The charging box is not fully charged, while the charging indicator light is steady red. When the battery is fully charged, the charging indicator is off. -During the charging of the headset, the red light of the earphone light is long. When the earphone is fully charged, the white light of the earphone light is on for 1 minute and then goes out.
1. When the earphone is in the charging box, the earphone is automatically turned on from the charging box.
2. When the headset is not in the charging box and is turned off, press and hold the multi-function button for about 1 second (the white light is on).
1.Put it into the charging box and the headset will automatically shut down. 2.When the power is on, press and hold the multi-function button for about 5 seconds (the red light is on for 2 seconds).
Automatically Connect: Take two earphones out of the charging box at the same time, wait for 2-3 seconds to automatically turn on the headphone, and turn on the device Bluetooth search “Redmi AirDots_R” when the right headphone white light flashes and click to complete the connection. If the connection fails, put the headset back in the charging case. Repeat the above operation. After the first connection, the headset can be automatically connected back to the last paired device (Bluetooth function needs to be turned on). Note: The headset has been initialized at the factory and can be taken out for related operations directly.
When the headset is turned off, manually open two headphones, the white light flashes quickly and waits for the left and right headphones to be connected in series. After the serial connection is successful, the right earphone white light flashes slowly, and the device Bluetooth is connected to connect.
Take out a headset from the charging idea. When the indicator light flashes from white light to slow network after auto power on, open the device Bluetooth search “Redmi ArDots_R” (or “Redni ArDos_L”) and click to complete the connection.
After the first connection, the headset can be automatically connected back to the last paired device (Bluetooth needs to be turned on). Note: The left earphone (L) has a relatively long automatic connection time.
Manual connection: When the headset is turned off, manually turn on one of the machines. When the headset turns white and flash slowly, turn on the Bluetooth function of the device to connect the corresponding headset.
If the headset cannot be connected properly, please reset the headset as follows: Take the headset out of the charging box, and in the off state, press and hold the two earphone multi-function keys for about 15 seconds, and alternately flash three times in the second red and white light. Then release and put back the charging box, delete the connection record on the device and reconnect. (including clearing the records where the two headphones are paired in series and paired with the device).
Redmi AirDots User Manual Source = Redmi
